Parts & Accessories

Chris King ISO XD Driveshell assembly, complete with ceramic bearings.

Chris King ISO XD Driveshell assembly, complete with bearings.

Chris King ISO XD Driveshell assembly conversion kit, no bearings.

- Freehub bodies include: (1) specified freehub body, (3) pawls, and (1) pawl spring - Freehub bodies do not include lockrings

Mavic's XD freehub body is compatible with all Crossmax and Deemax wheels (2012 and after) or all wheels using TS-2 hubs. This freehub body converts a rear wheel to work with SRAM's XD standard, making the wheel compatible with the XX1 drivetrain. Two kits are available : XD freehub body ITS-4 and XD freehub body TS-2, each with hub-specific parts.

Axle conversion kits are required for converting your current hub to be used on various other axle platforms. - Fits 135mm or 142mm Chris King ISO Rear Hubs (not compatible with 150mm, 157mm or Singlespeed Hubs) - Allows you to run a 135x10mm Thru Axle on 135mm or 142mm Chris King ISO Hubs - All axles require an adjusting clamp for installation

Axle conversion kits are required for converting your current hub to be used on various other axle platforms. - Fits 135mm or 142mm Chris King ISO Rear Hubs (not compatible with 150mm, 157mm or Singlespeed Hubs) - Allows you to run a 135x12mm Thru Axle on 135mm or 142mm Chris King ISO Hubs - All axles require an adjusting clamp for installation

Axle conversion kits are required for converting your current hub to be used on various other axle platforms. - Fits 135mm or 142mm Chris King ISO Rear Hubs (not compatible with 150mm, 157mm or Singlespeed Hubs) - Allows you to run a 142x12mm Thru Axle on 135mm or 142mm Chris King ISO Hubs - All axles require an adjusting clamp for installation

Axle conversion kits are required for converting your current hub to be used on various other axle platforms. - Large Diameter (LD) Axle for 15mm forks - Fits Chris King ISO LD Front Hubs (15mm and 20mm only) with serial numbers starting with 171 ONLY - Allows you to run a 15mm Axle on Chris King ISO LD Front Hubs - All axles require an adjusting clamp for installation

Axle conversion kits are required for converting your current hub to be used on various other axle platforms. - Small Diameter (SD) Axle for 15mm forks - Fits Chris King ISO SD Front Hubs (9mm and 15mm only) - Takes existing 9mm QR Chris King ISO Hubs and allows you to run a 15mm Thru Axle - All axles require an adjusting clamp for installation

Chris King never settles for anything but perfect, so you shouldn't either. This replacement axle replaces a damaged or worn axle on Small Diameter (SD) Chris King ISO front hubs designed to work with Quick Release skewered fork ends. To convert your ISO SD hub from a different axle standard to QR, you'll need this axle, along with the following parts: - ISO SD QR Front Axle End, Manufacturer's Part Number (MPN): PHB308 - 9mm Front Axle Adjustment Cone, MPN: PHB701

Original equipment freehub bodies to fit SRAM hubs and wheels.

Constructed of DuPont Cordura with taped seams for a durable, element proof bag. - Designed to hold one wheel: road or mountain - The padded center is double lined for durability - A small zippered inner pocket in the bag holds tools - Constructed of DuPont Cordura and is completely seam taped

- Syntace x-12 Rear axle standard creates a stiffer and lightweight rear end - Syntace x-12 Parts are only compatible with frames that have Syntace x-12 Dropouts

Travel in style with the Roval Single Wheel Bag. It features padded Cordura nylon construction and is reliably tough and weather-resistant, while the bag itself is built to accommodate a single wheel. Accommodates 26" and 700c sized wheels.

- Cassette Body Type: Shimano/SRAM 11 Speed Road - Material: Steel

Adjustment clamps are used to adjust bearing preload on Chris King hubs. - Includes one High Profile (HP) Adjustment Clamp - Fits all Chris King ISO/Disc Rear Hubs

Adjustment clamps are used to adjust bearing preload on Chris King hubs. - Fits Chris King ISO SD Front, and Classic Rear

Designed with today’s taller, double-digit cog stacks in mind, Chris King's R45 cassette lock rings feature longer threads to provide secure engagement with the hub driveshell. A Chris King cassette lock ring is the perfect complement to any Chris King hub, or for anyone looking to add a dash of King performance to other manufacturer’s compatible rear hubs. They are available for both 11 and 12 tooth small cogs, as well as Shimano or Campagnolo hubs.

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.

Stan's Enduro Rim Strip converts standard tubed wheels to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!

On today's road forks, there are multiple front axle standards. Mavic front axle adapters allow you to mix and match without replacing wheels/forks. Most Mavic wheels can be fitted with specific adapters to match your fork end dimensions. - Adapts Mavic road wheels to use 12mm front axle - One pair is required for each hub to be converted

On today's raod forks, there are multiple front axle standards. Mavic front axle adapters allow you to mix and match without replacing wheels/forks. Most Mavic wheels can be fitted with specific adapters to match your fork end dimensions. - Converts Mavic front hubs to 9mm - One pair required for each hub to be converted

On today's MTB frames, there are many dropout diameter and width standards. Most Mavic wheels can be fitted with specific adapters to match your wheelset with your frame. - Converts Mavic mountain hubs to quick release - One pair is required for each hub to be converted

Roval's rim-specific Tubeless Valves are designed to match Specialized's rim profiles and provide a better seal than previous generation valves. - Constructed of lightweight aluminum - Removable valve core - Mated with a seal which is specific to different rim models: - MY14 Control SL = black rim bed shaped seal - MY15 Control Carbon/Aluminum = red rim shaped seal - MY15 Traverse SL/Aluminum = black O-ring seal

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits Campagnolo / Italian rear hubs with 130mm spacing - Type: Hollow Axle - Threads: 10mm x 26tpi - Diameter: 10mm - Length: 141mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits Campagnolo / Italian rear hubs - Type: Solid Axle - Threads: 10mm x 26tpi - Diameter: 10mm - Length: 174mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 135mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 146mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese front hubs - Type: Hollow Axle - Threads: 9mm x 1 - Diameter: 9mm - Length: 110mm - 1 axle per bag