How To Fix A Flat Tire
Sooner or later, you'll get a flat tire. As long as you carry a few basic tools flat repair is easy—even fun! Here's how it's done. Note that these instructions are for standard tires and tubes, and tubeless setups, and for road and mountain bicycles, too.
2. Remove the wheel: Open the quick release (or loosen the axle nuts) on the wheel with the flat and lift the bike to remove the wheel. To extract rear wheels, it helps to pull the derailleur back slightly to clear the axle parts as the wheel passes through (main photo: click to enlarge). For fronts, you'll probably need to hold one side of the quick release and turn the other counterclockwise to create clearance to get past the wheel-retention ("safety") tabs on the fork (inset photo: click to enlarge).
3. Remove the tire and tube: Remove the valve cap and nut (sometimes found on Presta valves: inset photo: click to enlarge). For Presta valves, unscrew the tip and press down to let all the air out. For Schraders, poke the end of the tire lever into the valve to release all the air. Starting directly opposite the valve, wiggle a tire lever beneath the tire's edge and pry down to lift. If possible, hook the lever on a spoke (many levers are made to do this), or hold it in place. Place another lever about 4 inches away from the first and pry here (main photo: click to enlarge). Continue with your third lever until you can get one side of the tire off. Then reach inside and fully extract the tube. Pull the other side of the tire off the same side of the wheel or pry it off with the levers.
4. Inspect the tire: It's important to find whatever caused the flat and remove it. If you don't, the culprit might still be in the tire where it'll just pop your new tube! To find it, remove your glove (or use a rag), and run it around inside the tire in both directions (photo: click to enlarge). If something sharp is still stuck in your tire, it'll snag the glove. Remove the nasty. If you can't find anything, it's likely it got knocked out during the disassembly procedure.
5. Install the tube & tire: 4 Easy Steps
2) Place the valve partway into the hole and simultaneously push the top section of the tire edge (called the "bead") that's at the valve and closest to your legs onto the rim. Then, with both hands moving downward away from the valve using the ground to push against, finish working the bottom tire bead (the one closest to your legs) onto the wheel all the way around the wheel (photo: click to enlarge).
4) With a few inches of bead left to pop onto the rim, the tire will resist. Let all the air out. Crouch and rest the wheel on your knee to have something to push against. Now, hold the bead in place with one hand (we're using our left hand in the photo: click to enlarge) and with your stronger hand, push down to roll the stubborn section onto the rim with the heel of your hand. But don't try to pop it on all at once. Install an inch at a time, moving your hand along until you've fully installed the tire. If it resists, be sure all the air is out of the tire. Got it? Good job!
6. Inflate and seat the tire and reinstall the wheel: Place your pump on the valve and inflate the tire. To prevent valve damage, brace the valve by wrapping a finger behind a spoke and your thumb over the tire (photo: click to enlarge) so you're pushing against your hand, not the valve. And hold the pump steady, don't wiggle it around as you pump. Inflate the tire until it's just firm (not fully inflated). At this point, inspect the tire to make sure it's "seated," which means that it's sitting correctly on the wheel.
If the tube gets trapped beneath a bead (photo, below, left: click to enlarge), inflating further may blow the tire and tube off the rim! There are bead lines on the sides of the tire that should be equidistant from the rim all the way around on both sides of the wheel. If they're not, or if you see a section of tube peeking out from under the tire (photo), let the air out, poke the tube gently back into place with your tire lever (don't even think of using a screwdriver, which will pop the tube), reinflate partway and check the tire again.
From the best pumps, to spare tubes, patch kits and flat-resistant tires and tubes, we have everything you need to ensure that you have a minimum of flat tires and an easy time fixing flats, too. We can also show you how to fix a flat. Just ask if you need any help at all. Thanks!