Campagnolo's Record EPS V2 Power Unit is the reliable brain of Campy's electronic shifting. In order to keep your bike looking sleek, the mounting options allow it to sit inside your bike's frame. The 3-cell, 12-volt Lithium-ion battery delivers up to 1,200 miles on a single charge. It also houses the electronics necessary to deliver pinpoint shifting precision to the front and rear derailleur mechanisms (sold separately). For example, if you're cross-chained, the system immediately senses it and moves the front derailleur ever so slightly to avoid chain rub. Plus, the one-piece, ultrasonically-sealed unit is impervious to water or road vibration.

The EPS Power Unit is the systems source of power as well as the "brain" of the system, responsible for managing the battery pack, enabling and monitoring the front and rear derailleurs and communicating with the Interface Unit. - Weathertight, o-ring sealed connectors - Lithium Ion battery duration: 500km/month - 1500km, 1000km/month - 1800km, 2000km/month - 2000km - Water proof to 1m for 30 minutes (IP67 Rated) - Operational temperature: -4F to 140F - Charging temperature: 32F to 113F - 17mm diameter for easy seat post installation - Battery charges through the Interface Unit - Compatible only with the Super Record/Record V3 Power Unit

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 17mm - Outer Diameter: 30mm - Width: 7mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 15mm - Outer Diameter: 24mm - Width: 5mm

Shimano Di2 External Battery Mount - All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions - Use Di2 system checker to update component firmware

Shimano's Di2 electric drivetrain takes shifting to the next level. Two Di2 Battery Chargers are available. Choose the model designed for your system's battery. An additional power cable is required for the external-style battery charger (sold separately). These chargers fully charge the battery in 90 minutes.

Service your DT Swiss star ratchet hubs and wheels with DT Swiss Ratchet and Kits. - DT Swiss EXP 54 Tooth Upgrade Kit

- Lever Assembly, Aluminum lever Gen 2, Black Ano (assembled, no hose, and includes barb and olive), Guide RSC

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 10mm - Outer Diameter: 26mm - Width: 8mm

Featuring more tunability than ever before, the Megneg air can provides an even larger negative volume giving you more mid-stroke support, a plusher initial feeling, and more bottom out force using less tokens. Go ahead and tune your shock exactly to your ride. - Includes air can, tokens, seals & decals - Compatible with Deluxe and Super Deluxe rear shocks

ReMote Dropper Lever - Lever pivots on a 21mm ball bearing for smooth operation - Cable Kind Clamp does not damage secured cables and features captive hardware. - Includes barrel adjuster for on the fly changes - Engineered break-away pivot that allows the lever to break away from the pivot in the event of a crash.

Campagnolo Chainring Bolts

The ReMote BarCentric is a dropper lever option for bikes with front shifters, lockout levers, or e-bike controls. The slender design of the ReMote BarCentric allows it to easily fit between the left grip and levers with four potential lever positioning options to avoid any interference with existing levers. This dropper lever has a ring shape that encompasses the handlebar, while also serving as a pivot point to provide the rider with extra leverage, making it easier to press the lever. - Compatible with left side controls including 2x shifters, suspension lockout levers, and under-bar e-bike controls - Large, smooth, sealed Enduro ball bearing that encircles the handlebar - Clean and efficient cable routing flows around disc brake levers - Adjustable reach for ideal ergonomics and controls clearance - Compatible with all cabled actuated dropper posts - Works with dropper posts that have the barrel end of the cable at the remote and those that have the barrel end at the post - Works with any mountain bike handlebar - Can be rotated to your preferred position

ReMatch adapters are designed to integrate different generations of Shimano Brakes to Shimano Shifters. Rematch Adapter 1.2 connects Shimano I-Spec A/B brake to I-Spec II Shifter. - Made from CNC Machined T6061 Aluminum - Anodized Black - Includes all necessary hardware for both I-Spec A and I-Spec B brake - No additional hardware needed

Specialized Turbo Road Remote

Wolf Tooth ReMote Light Action has a longer lever arm than the standard ReMote and is optimal for dropper posts with a harder pull or for riders that just prefer a really light actuation feel. It reduces the force to actuate a dropper by nearly a third of the standard ReMote. Based on rider feedback and tailored to work with some posts' stiffer internal springs, the ReMote Light Action is also the choice of those with thumb injuries or reduced hand strength. - Upfront cable fixing - Large diameter ball bearing - Cable-kind clamp - Low-profile, light action - Integrated cable adjust - Breakaway axle pivot - High-traction lever - Broad compatibility

Campagnolo Cable Anchor Assembly Caliper Brake Part

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - CNC machined 6061 aluminum - Black anodized finish - Made in the USA

Campagnolo Chainring Bolts

Campagnolo lockrings for use with N3W freehubs only. - Aluminum construction

Campagnolo Ultra Torque Cup and Bearing Kits. Includes 2 bearings and 2 seals. - Kit includes 2 bearings and 2 seals

The Problem Solvers Cable Doublers are made of light, durable machined and anodized aluminum and they are Teflon coated for a super-smooth cable pull every time. They come in two models. The first allows you to control two brakes with one lever. The second allows you to control one brake with two levers. Why? Well, there are myriad applications: tandems, cyclocross bikes, fixies, tricycles, recumbents, cycles for those with special needs, bike polo bicycles, those 4-person bikes you see on beach boulevards, and so on. You could even link both models of Cable Doublers together for the ultimate in redundancy!

RockShox's Maxle Lite is a lightweight aluminum through-axle system. It lets you remove and install your wheel as fast as with a standard quick-release while delivering the awesome stiffness with the improved strength and control of a through-axle. Plus, the lever can be closed in whatever position you like and no tools are required for installation and use!

Surly Mr. Whirly Spindles. - 100% CroMoly steel - Proprietary dimensions and spline for use only with Surly Mr. Whirly cranks

Campagnolo Pulley Assemblies

Hellbender bearings have an improved seal structure and are cross compatible with Cane Creek headsets.

Mounted in place of a front derailleur, the Chain Keeper works with single and 1x multi speed drivetrains using a narrow chain. The chain block surrounds the chain as it meets the chainring and prevents it from skipping off. - Accommodates a range of chain line measurements and chainring sizes - Not designed for downhill/freeride/big hit use

RockShox XLoc Parts

Campagnolo Chainring Bolts

The Problem Solvers Head Tube Reducers resize your head tube to accommodate different size forks. These fine aluminum reducers are designed for traditional, external-cup headsets. Please contact us for any questions about compatibility with your bicycle.

Surly Singleator mounts right up to your derailleur hanger and provides a simple, effective, and adjustable means of tensioning the excess chain slack found in vertical dropout single-speed drivetrains. - Triple-sealed spring, large cog capacity and chain guides - Stainless steel pivot bushing - Includes two springs for upward or downward tension adjustment - Do not use with a coaster brake, fixed gear, multi-cog or multi ring drivetrains

Wheels Manufacturing's SRAM compatible Universal Derailleur Hanger simplifies thousands of hanger designs into one universal standard. Machined completely out of aluminum, this new hanger is not only strong but designed to rotate backward and slip slightly in the case of an impact preventing chain jams and protecting the drive train. All Wheels Manufacturing replacement derailleur hangers are produced in our Colorado shop to exacting tolerances. - Compatible with bike frames designed to accept the SRAM UDH (Universal Derailleur Hanger) - Compatible with all MTB and eMTB drivetrains - Machined aluminum body anodized black - Thru-Axle thread pitch M12 x 1

These simple clamps allow riders to mount I-Spec II compatible shifters or dropper levers onto their bars without the otherwise-requisite Shimano I-Spec II compatible brake levers. Sold individually and can be used for either right- or left-hand side. - Hinged clamps for easy installation without removing other components - AL-6061, anodized black - 23 grams - For use only with I-Spec II compatible shifters or dropper lever

Original equipment hydraulic hoses for no-compromise brake performance. - Fits All B (2016+) Versions of Guide RSC RS R - Hose length: 2000mm

All Wheels Manufacturing replacement derailleur hangers are produced in their Colorado shop to exacting tolerances. - CNC machined 6061 aluminum - Black anodized finish - Includes (2) M4x8 Flat Head Screws Note: Included hanger hardware is 1mm too long, it is suggested that existing hanger hardware be used!

- Asymmetrical design with an offset slot specifically for carbon seatposts - Fitment based upon seattube sizes: 34.9-35.2 For 31.6 Posts. - 24g

Chris King Headset Conversion Kits that allow conversion from one style to another in the same size. - Kit includes a stem cap, screw, star nut, scuff washer, and bearing cap, all the pieces you'll need to convert an existing threaded Chris King Sealed Bearing headset to a NoThreadSet - King offers 2 versions of this kit, our version does not include base plate

Service your suspension fork with the Enduro HyGlide Fork Seal Kit. HyGlide seals utilize the material and design advantages of our two-part seals (Polyurethane wipers and Moly-Disulphide-infused oil seals) and combine them into a single wiper/oil seal. This unique design joins the oil seal and wiper into a single unit, creating a sealing system that eliminates one of the sealing lips and decreases seal friction or “stiction” by 25%. The cold-fused integrated seal design also features a large oil cavity between the two sealing lips to prevent contamination and further ease fork's movement. - HyGlide seal superior sealing action and can increase fork service intervals by as much as 2 or 3 times compared to OE recommendations

The Tanpan brings the range and security of Shimano mountain rear derailleurs to Shimano-equipped drop-bar bicycles. This means a greater gearing range for bigger adventures, better chain security for rough terrain, and lighter weight and reduced complexity for the daily commute. In order to deliver these benefits, the Tanpan amplifies road shifter cable pull to allow for seamless communication with mountain derailleurs. The result is ideal for riders looking to convert their road, gravel, cyclocross, or commuter bike to the simplicity and light weight of a single chainring. - Not Compatible with Tiagra 4700 - Compatible with most road, CX and gravel bikes - Designed to mount directly to adjuster-free cable stops on Shimano rear derailleurs - Certain chainring and cassette configurations benefit from a Goatlink - If the rear derailleur cable is routed internally through the chainstay and exits at the end of the chainstay above the axle or past the axle out the very end, you will need to utilize the inline ferrule

Original equipment rear derailleur pulleys for SRAM rear derailleurs. Fits X01, X01DH, X1, GX 1x11, NX, Force CX1, Force 1, Rival 1, Apex 1 Derailleurs. - Wide-narrow pulley tooth profile holds the chain better - Stainless steel sealed cartridge bearings

Dimension Steerer Extender adds 2 to 3-1/4" height to steerer. - Extender clamps to steerer; stem clamps to extender - Adds 2 to 3-1/4-inch height to threadless steerer - Includes top cap and long bolt - 40mm of threadless steerer is required for proper installation - Do not stack steerer extenders; no more than one steerer extender recommended per bike - WARNING: Dimension Steerer Extender is not recommended for use on forks with carbon fiber steerers

ABI Headset Bearing for new builds or replacements.

One of the single biggest improvements you can make to your fork. Engineered and developed over several years, the PUSH Ultra Low Friction fork seals provide class leading sealing while offering incredibly low friction, resulting in an increase in small bump sensitivity. - Advanced friction-reducing, Molybdenum filled material increases small bump sensitivity while also increasing durability - Dual scraping lip design provides maximum scraping effect while minimizing friction - Loaded oil sealing lip integrated into wiper to keep lower leg fluid from escaping fork, increasing performance and durability - High-volume, absorbent foam rings ensure consistent lubrication improving seal life and bump sensitivity - Molded utilizing precision 3D machined molds for exact tolerance

Hose fittings fit many of SRAM's newest hydraulic brake models. - Includes 5 Threaded Hose Barbs, 5 Compression Fittings, 1 T8 Torx Wrench - Fittings are backwards compatible with older SRAM and Avid hydraulic brakes

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA

Campagnolo lockrings for use with N3W freehubs only. - Aluminum construction

Campagnolo Power Torque Cup and Bearing Kits - Fits all Campagnolo Power Torque cranks - Kit includes 2 bearings and 2 outer seals

Campagnolo Pulley Assemblies

These baseplates are the foundation that keeps Chris King headsets turning with legendary smoothness. Manufactured from high-quality stainless steel or titanium, Chris King makes replacement baseplates for all standard sizes and a number of ingenious solutions for those that need something a little special to make their headset work. - Engineered and manufactured in Portland, Oregon USA - High-quality stainless steel and titanium baseplates available for all standard Chris King headset sizes - Titanium baseplates are available in 1-inch and 1 1/8-inch sizes only - Devolution baseplates are a stainless steel solution that allow King headsets to adapt to a wide variety of steerer tube sizes - King Stainless Steel baseplates are available in undersized and oversized versions for irregular steerer tube sizes - 30.0mm ID/40.5mm OD for post-April 1995 1-1/8" Headsets - 30.0mm ID/44.0mm OD for pre- April 1995 1-1/8" Headsets

Clamp allows use of a braze-on derailleur on frames without the braze-on tab. Includes a tab to use SRAM's lightweight and easy-to-adjust chain control device. - Fits all SRAM road braze-on front derailleurs - ChainSpotter not included

Ergonomic design for comfort in a variety of hand positions. -Compatible with SRAM eTap Shifting/Brake Levers

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - CNC machined 6061 aluminum - Black anodized finish - Made in the USA

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - These hangers DO NOT INCLUDE attachment hardware with the exception of QBP # FS1561 (DROPOUT 399) - CNC machined 6061 aluminum - Made in the USA

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - CNC machined 6061 aluminum - Black anodized finish - Made in the USA

Wheels Manufacturing hangers are stiffer than almost any OEM hanger, which improves durability and shifting performance. - OEM hangers are only produced by a handful of manufacturers, mostly in Taiwan and China. As a result, you will see many bikes with exactly the same hanger. Bicycle manufacturers may make mid year changes. Please use the hanger photos to select the proper hanger for your application. - CNC machined 6061 aluminum - Black anodized finish - Made in the USA

The RoadLink DM (Direct Mount) is the RoadLink designed to fit Shimano's current generation R8000 Ultegra and R9100 Dura-Ace rear derailleurs. It serves as a simple device to offset the position of the rear derailleur, making it possible to run a wide-range mountain bike style cassette. It's an ideal solution for riders looking to convert their road, gravel, cyclocross, or commuter. - Fits Shimano R9100-generation Dura-Ace and R8000-generation Ultegra rear derailleurs - CNC machined from 6061-T6 aluminum with stainless steel bolt - Does not change the derailleurs total chain wrap capacity - Fits standard derailleur hangers only - Best used with Single or Double Setups - see manufacturer's site for more details

- AL6061-T6 alloy seatpost clamp - Rounded edges and floating bolt/ovalized hole design protects carbon frames and seatposts - 28.6mm for 25.4mm seat post and steel frame - 29.8mm for 27.2mm seat post and chromoly frame - 31.8mm for 27.2mm seat post and aluminum frame - 34.9mm for 30.9mm seat post and aluminum frame, or 31.6mm seat post and carbon frame - 16mm height

GX Eagle Rear Derailleur Pulley Kit